Model

Illustration/Image

Overview

DAS72.1

Digital Load Cell Amplifier - NEW MARK III VERSION
 - Now with non-volatile tare and peak hold facilities
 - DIN rail mounted, 11-25V DC supply with digital display, Zero and Tare buttons
 - 600 readings per second transmitted, Reading between -99,999 and + 99,999 counts
 - 4-20 mA analogue output, 3 programmable Logic Inputs and 3 Logic outputs,
 - RS422/485 interface. Fast easy calibration using the load cell mV/V sensitivity
 - 18 bit resolution, linearity better than 0.002%, selectable filter 0.25 - 19.7 Hz
 - Designed to drive 4 off 350 Ohm load cells ±3.2mV/V maximum

LAC65.1

Analogue Load Cell Amplifier

 - DIN rail mounted, 12-24V DC supply
 - 0/4-20 mA and 0-±10V analogue outputs available at the same time
 - Zero offset up to ±80% of range, minimum signal 0.17mV/V to achieve full scale
 - Linearity better than 0.010%, selectable filter 0.25 - 32 Hz
 - Designed to drive 4 off 350 Ohm load cells ±3.3mV/V maximum

LAC74.1

Analogue Load Cell Amplifier

 - DIN rail mounted, 12-24V DC supply
 - 0/4-20 mA or 0-10V analogue outputs selectable
 - Zero offset up to ±90% of range, minimum signal 0.10mV/V to achieve full scale
 - Linearity better than 0.010%, selectable filter 0.33 - 33 Hz
 - Designed to drive 4 off 350 Ohm load cells +3.5mV/V maximum

LAU63.1

Analogue Load Cell Amplifier Module (Force Measurement)

 - 12-24V DC supply, optional DIN rail adaptor with screw terminal connections (UA73.2)
 - 0-±10V analogue output for force measurement applications
 - Zero offset up to ± 0.7 mV/V, minimum signal 0.40mV/V to achieve full scale
 - Linearity better than 0.010%, selectable filter 3.3 - 3300 Hz
 - Designed to drive 1 off 350 - 2000 Ohm load cell  ±3.2mV/V maximum

LAU73.1

Analogue Load Cell Amplifier Module

 - 12-24V DC supply, optional DIN rail adaptor with screw terminal connections (UA73.2)
 - 0/4 - 20mA analogue output or 0-10V by the addition of optional 500 Ohm resistor
 - Zero offset up to 65% of range, minimum signal 0.25mV/V to achieve full scale
 - Linearity better than 0.010%, selectable filter 0.33 - 33 Hz
 - Designed to drive 1 off 350 - 2000 Ohm load cell, input range -0.2 - 2.3 mV/V

LDU68.1

Digital Load Cell Amplifier Module (R76 Approved 5000d)

 - Approved to R76 5000d 0.7uV/d, 12 -24V DC supply. RS422 communication port
 - Designed to drive 1 off 250 - 2000 Ohm load cell, Input range ± 2.2 mV/V
 - 30 samples/second at greater than 16 bit resolution, Linearity better than 0.002%
 - 2 logic inputs and 2 logic outputs, supplied with simple pin connectors (not mounted)
 - Optional DIN rail adaptor with screw terminal connections and on board fuse (UA73.2).

LDU68.2

Digital Load Cell Amplifier Module

 - 12 -24V DC supply. RS422 communication port
 - Designed to drive 1 off 250 - 2000 Ohm load cell, Input range ± 2.2 mV/V
 - 30 samples/second at greater than 16 bit resolution, Linearity better than 0.002%
 - Supplied with simple pin connectors (not mounted)
 - Optional DIN rail adaptor with screw terminal connections and on board fuse (UA73.2).

LDU69.1

Digital Load Cell Amplifier Module (R76 Approved 10,000d)

 - Approved to R76 10,000d 0.1uV/d, 12 -24V DC supply. RS422 communication port
 - Designed to drive 1 off 250 - 2000 Ohm load cell, Input range ± 2.2 mV/V
 - 172 samples/second at 19 bit resolution, Linearity better than 0.002%
 - Extremely low temperature drift typically 1ppm/°C zero and span,
 - Supplied with simple pin connectors (not mounted)
 - Optional DIN rail adaptor with screw terminal connections and on board fuse (UA73.2).

LDU78.1

Digital Load Cell Amplifier Module (R76 Approved 5000d)

 - Approved to R76 5000d 0.7uV/d, 12 -24V DC supply. RS422 communication port
 - Designed to drive 1 off 250 - 2000 Ohm load cell, Input range ± 2.2 mV/V
 - 600 samples/second at 17 bit resolution, Linearity better than 0.002%
 - 2 logic inputs and 2 logic outputs, supplied with simple pin connectors (not mounted)
 - Optional DIN rail adaptor with screw terminal connections and on board fuse (UA73.2
 - Available with Check Weigher Firmware

QLC62.1

Digital Load Cell Amplifier (R76 Approved 10,000d)

 - Approved to R76 10,000d 0.1uV/d, 12 -24V DC supply. RS232/485 comms ports
 - Designed to drive up to 8 off 350 Ohm load cell, Input range  ± 3.5 mV/V
 - 4 independent input channels which can be read/calibrated individually or as a group
 - Linearity better than 0.005%, resolution selectable between 12 and 20 bit
 - Supplied in die cast aluminium housing complete with 6 cable glands

SGM430

Analogue Load Cell Amplifier

 - DIN rail mounted, 16-30V DC supply
 - 0/4-20 mA and 0-10V analogue outputs available at the same time
 - Zero offset up to 18% of range, minimum signal 0.30mV/V to achieve full scale
 - Linearity better than 0.020%, selectable filter 0.25 - 250 Hz
 - Designed to drive 4 off 350 Ohm load cells +2.5mV/V maximum

SGM450

Digital Load Cell Amplifier Module (R76 Approved 4000d)

 - Approved to R76 4000d 1uV/d, 15 -28V DC supply. RS232 & RS422 comms. ports
 - 10 -28V DC supply. RS232 and RS422 comms ports
 - Designed to drive 6 off 350 Ohm load cell, Input range  3.5 mV/V
 - 50 samples/second at 100K bit resolution, Linearity better than 0.003%
 - Selectable baud rates between 9K6 and 57K6
 - Din rail mount
 

SGM500

Digital Load Cell Amplifier (R76 Approved 4000d)

 - Approved to R76 4000d 1uV/d, 15 -28V DC supply. RS232 & RS422 comms. ports
 - Designed to drive 4 off 350 Ohm load cells, Input range  + 2.0 mV/V
 - 500 samples/second at 100K bit resolution, Linearity better than 0.003%
 - 4 logic inputs and 4 power FET outputs
 - Selectable baud rates between 9K6 and 57K6